Description
CY7C63310-SXC: USB Interface IC USB Peripheral Cntrl 3K/128 16-SOIC
Package: SOIC-16
Mfr. Part#: CY7C63310-SXC
Mfr.: CYPRESS
Datasheet: 
(e-mail or chat us for PDF file)
ROHS Status:
Quality: 100% Original
Warranty: 180 days
Cypress has reinvented its leadership position in the low speed USB market with a new family of innovative microcontrollers. Introducing enCoRe II USB - 'enhanced Component Reduction.' Cypress has leveraged its design expertise in USB solutions to advance its family of low speed USB microcontrollers, which enable peripheral developers to design new products with a minimum number of components. The enCoRe II USB technology builds on the enCoRe family. The enCoRe family has an integrated oscillator that eliminates the external crystal or resonator, reducing overall cost. Also integrated into this chip are other external components commonly found in low speed USB applications, such as pull-up resistors, wakeup circuitry, and a 3.3 V regulator. Integrating these components reduces the overall system cost.The enCoRe II is an 8-bit flash programmable microcontroller with an integrated low speed USB interface. The instruction set is optimized specifically for USB and PS/2 operations, although the microcontrollers may be used for a variety of other embedded applications.The enCoRe II features up to 20 GPIO pins to support USB, PS/2, and other applications. The IO pins are grouped into four ports (Port 0 to 3). The pins on Port 0 and Port 1 may each be configured individually while the pins on Ports 2 and 3 are configured only as a group. Each GPIO port supports high impedance inputs, configurable pull-up, open drain output, CMOS/TTL inputs, and CMOS output with up to five pins that support a programmable drive strength of up to 50 mA sink current. GPIO Port 1 features four pins that interface at a voltage level of 3.3V. Additionally, each IO pin may be used to generate a GPIO interrupt to the microcontroller. Each GPIO port has its own GPIO interrupt vector; in addition, GPIO Port 0 has three dedicated pins that have independent interrupt vectors (P0.2-P0.4).
- USB 2.0-USB-IF certified (TID # 40000085)
- enCoRe™ II USB - 'enhanced Component Reduction'
- Crystalless oscillator with support for an external clock. The internal oscillator eliminates the need for an external crystal or resonator.
- Two internal 3.3 V regulators and an internal USB Pull-up resistor
- Configurable I/O for real world interface without external components
- USB Specification compliance
- Conforms to USB Specification, Version 2.0
- Conforms to USB HID Specification, Version 1.1
- Supports one low speed USB device address
- Supports one control endpoint and two data endpoints
- Integrated USB transceiver with dedicated 3.3 V regulator for USB signalling and D- pull-up.
- Enhanced 8-bit microcontroller
- Harvard architecture
- M8C CPU speed is up to 24 MHz or sourced by an external clock signal
- Internal memory
- Up to 256 bytes of RAM
- Up to eight Kbytes of flash including EEROM emulation
- Interface can auto configure to operate as PS/2 or USB
- No external components for switching between PS/2 and USB modes
- No General Purpose I/O (GPIO) pins required to manage dual mode capability
- Low power consumption
- Typically 10 mA at 6 MHz
- 10 µA sleep
- In system reprogrammability
- Allows easy firmware update
- GPIO ports
- Up to 20 GPIO pins
- 2 mA source current on all GPIO pins. Configurable 8 or 50 mA/pin current sink on designated pins.
- Each GPIO port supports high impedance inputs, configurable pull-up, open drain output, CMOS/TTL inputs, and CMOS output
- Maskable interrupts on all I/O pins
- A dedicated 3.3 V regulator for the USB PHY. Aids in signalling and D- line pull-up
- 125 mA 3.3 V voltage regulator powers external 3.3 V devices
- 3.3 V I/O pins
- 4 I/O pins with 3.3 V logic levels
- Each 3.3 V pin supports high impedance input, internal pull-up, open drain output or traditional CMOS output
- SPI serial communication
- Master or slave operation
- Configurable up to 4 Mbps transfers in the master mode
- Supports half duplex single data line mode for optical sensors
- 2-channel 8-bit or 1-channel 16-bit capture timer registers. Capture timer registers store both rising and falling edge times.
- Two registers each for two input pins
- Separate registers for rising and falling edge capture
- Simplifies the interface to RF inputs for wireless applications
- Internal low power wakeup timer during suspend mode:
- Periodic wakeup with no external components
- 12-bit Programmable Interval Timer with interrupts
- Advanced development tools based on Cypress PSoC® tools
- Watchdog timer (WDT)
- Low-voltage detection with user configurable threshold voltages
- Operating voltage from 4.0 V to 5.5 V DC
- Operating temperature from 0 °C-70 °C
|
Package
|
|
|
|
Product Status
|
|
|
|
Protocol
|
|
|
|
Function
|
|
|
|
Interface
|
|
|
|
Standards
|
|
|
|
Voltage - Supply
|
|
|
|
Current - Supply
|
|
|
|
Operating Temperature
|
|
|
|
Package / Case
|
16-SOIC (0.154", 3.90mm Width)
|
|
|
Supplier Device Package
|
|
|
|
Base Product Number
|
CY7C63310
|
Company Product Line
Certificates
Why choosing us
- Located in Shenzhen, the electronic market center of China.
- 100% guarantee components quality: Genuine Original.
- Sufficient stock on your urgent demand.
- Sophisticated colleagues help you solve problems to reduce your risk with on-demand manufacturing
- Faster shipment: In stock components can ship the same day .
- 24 Hours service
Notice:
- Product images are for reference only.
- You can contact sales person to apply for a better price.
- For more products, Pls do not hesitate to contact our Sales team.
Audited Supplier 
(e-mail or chat us for PDF file)
){kind=link}